KEYA

HomeProductsBrushless Dc Motor ControllerDual Channel Brushless Dc Motor Controllerdual channel brushless dc servo controller
Contact Supplier
Mag Hao

Ms. Mag Hao

Leave a message

dual channel brushless dc servo controller

Payment Type:
L/C,T/T,D/P,Paypal,Western Union
Incoterm:
FOB,EXW
Min. Order:
1
Transportation:
Ocean,Land
Port:
QingDao,ShangHai,BeiJing
Share:
Chat Now
  • Product Description
Overview
Product Attributes

Model No.KYDBL4875-1E

Brandkeya

CertificationCE

Supply Ability & Additional Information

TransportationOcean,Land

Place of OriginChina

Supply Abilitythree days

CertificateCE ISO2019

HS Code9032899090

PortQingDao,ShangHai,BeiJing

Payment TypeL/C,T/T,D/P,Paypal,Western Union

IncotermFOB,EXW

I. Overview:

    KYDBL4875-1E is an intelligent Brushless Dc Controller.  
    It adopts 32-bit high-performance MCU,Advanced motion control algorithm is suitable to the outside of the quadrature encoder input to complete the     open loop and closed loop speed, under the closed loop torque of motor sport.Controller with multiple analog input port, the pulse input port and digital I/O port, can through the special software to redefine its functions.Universal RS232 serial port communication, CAN bus, CAN be widely used in automation.

II. Product Features:
  1. Wide-range voltage input, 10-55V.
  2. Intelligent PID control loop.
  3. Working mode: Speed open-loop, close-loop control, torque close-loop control, position close-loop control.
  4. External potentiometer, 0-5V analog quantity or pulse command control mode, RC (pulse width signal outputted by the receiver of aeromodelling remote control) control mode.
  5. Safety forward & reverse control, four-quadrant operation, support regeneration.
  6. Enable control function.
  7. Maximum current control.
  8. 4-way input port; the function can be defined as analog input, pulse input or digital input functions.
  9. 2-way digital (MOS tube open-drain) output, Generally as 24V 1A output
  10. (maximum load capacity of 40V 1A), can be used to loosen the brake or
  11. other attachments.
  12. Abnormalities like overcurrent, overheating, overvoltage and short circuit will start the protection function.
  13. LED status indicator.
  14. CAN bus communication, see the detailed communication protocol when using it.
  15. RS232 communication, see the detailed communication protocol when using it.

III: Performance Index: 

  • Power voltage: 10-55VDC.
  • At the ambient temperature 25℃, continuous working current 40A, transient current up to 75A 30S.
  • Out +5VDC power (It can power up the encoder): 5V DC  20mA
  • Analog input range: 0-- 5VDC
  • Impulse input range: 500Hz—5000Hz (corresponding maximum speed)
  • [Note] The minimum impulse frequency may change along with the setting of maximum speed.
  • Input range of duty ratio 0%-- 100% (input frequency range f ≤1KHz, recommend to use the frequency of 250Hz).
  • the digital output interface: 2 road, open drain, maximum load capacity of 40 V 1 A
  • Temperature protection status: When the temperature is 70℃, the controller will reduce output by overheating protection and will stop output when the temperature is 80℃.
  • Working temperature: -30℃-- +60℃.
  • Ambient humidity: Relative humidity≤80RH.
  • Boundary dimension: L * W * H = 148mm * 117mm * 75mm
  • Weight: 1000g

IV:General connect drawing

24V Bldc Motor Driver

V:DR15 terminals definitions:

Interface definition
Function
Remark
Software I/O
1
Failure alarm output terminal
IT CAN BE SET
DOUT2
2
Tx-out
RS232_Tx

3
Rx-in 
RS232_Rx

4
SUSPEND


5
GND
0 V

6
CANL
CAN-low

7
CANH
CAN-high

8
SUSPEND


9
Fault alarm output
IT CAN BE SET

10
Enable control EN
Effective for high level
DIN5
11
Forward and reverse control DIR
Effective for high level
DIN4
12
Speed Signal input IN
Frequency/Analog
P/AIN3
13
GND


14
Controller output DC 5V(20mA)


15
Brake Stop
Effective for high level

V:DR09 terminals definitions:

Definition of interfac
Function
Remark
1
Controller output DC 5V (20mA)

2
Brushless motor Hall wire---A

3
Brushless motor Hall wire---B

4
Brushless motor Hall wire---C

5
GND

6
Controller output DC 5V (20mA)

7
Encoder feedback input---A+

8
Encoder feedback input---B+

9
GND

If you need more information, please download the 24v 48v Bldc Controller user manual, hope that will help you.

Product Categories : Brushless Dc Motor Controller > Dual Channel Brushless Dc Motor Controller

Download
Email to this supplier
  • *Subject:
  • *To:
    Ms. Mag Hao
  • *Email:
  • *Message:
    Your message must be between 20-8000 characters
Send Inquiry
*
*

HomeProductsBrushless Dc Motor ControllerDual Channel Brushless Dc Motor Controllerdual channel brushless dc servo controller
Related Products List

Home

Product

Phone

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send